Linksys HomeLink HPPO200 User Manual

HomeLink™SeriesPhoneline 10MCable/DSLRouterUser GuideUse this guide to install: HPRO200

7. Unless you already have a DHCP server on your internal network, chooseEnable from the DHCP Server field. By choosing Enable, you will con-figure th

6. Windows will ask you to restart the PC. Click the Yes button.Repeat steps 1-6 for each PC on your network. When all of your PCs areconfigured, the

Phoneline 10M Cable/DSL Router18On the following pages you will find brief descriptions of each utility web-pageand each page’s more important functio

Phoneline 10M Cable/DSL Router20It is strongly recommended that you set a password for the HomeLinkPhoneline Router. When you first power up the HomeL

Phoneline 10M Cable/DSL Router22• WA N These fields display the HomeLink Phoneline Router’s IP Address,Subnet Mask and Gateway IP, as seen by external

Phoneline 10M Cable/DSL Router244. Enter the HomeLink Phoneline Router’s administration password into thePassword Confirm box.5. Click the Browse but

Phoneline 10M Cable/DSL Router26Forwarding is generally used to set up a webserver, ftp server, or e-mail serveron your network. To add a server using

To create a static route entry:1. Select Static Route Entry from the drop down list. The HomeLinkPhoneline Router supports up to 20 static route entr

TroubleshootingThis section provides possible solutions to problems regarding the installationand operation of the HomeLink Phoneline Router. Read bel

• If you are connecting to a cable modem, try plugging the cable modeminto the HomeLink Phoneline Router’s uplink port rather than a 10BaseTport.• If

COPYRIGHT & TRADEMARKS Copyright © 2001 Linksys, All Rights Reserved. HomeLink is a registered trademark ofLinksys. Microsoft, Windows, and the

Web page hangs,corrupt downloads, or nothing but junk characters are being dis-played on the screen. What do I need to do? Force your NIC to 10Mbps or

AppendixVirtually all Internet addresses are configured with words or characters (i.e.,www.linksys.com, www.yahoo.com, etc.) In actuality, however, th

1. At the DOS command prompt, type “ping -a 24.53.32.4”, where24.53.32.4 is the IP address you just pinged. Information such as the fol-lowing data wi

7. After a few seconds you will be brought back to the main Network window.The TCP/IP Protocol should now be listed. 8. Click OK. Windows may ask for

There are different grades, or categories, of twisted-pair cabling. Category 5is the most reliable and is highly recommended. Category 3 is a good sec

Dynamic Routing - The ability for a router to forward data via a different routebased on the current conditions of the communications circuits. For ex

PPPoE (Point to Point Protocol over Ethernet) - A method used mostly by DSLproviders for connecting personal computers to a broadband modem forInterne

SpecificationsStandards: IEEE 802.3 (10BaseT), IEEE 802.3u (100BaseTX),HPNA 1.0, 1.1, and 2.0 CompatibleProtocol: CSMA/CDPorts: WAN: One RJ-45 Port

Warranty InformationBE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODEFROM THE PRODUCT'S PACKAGING ON HAND WHEN CALLING.RETURN REQUESTS CANNOT

Phoneline 10M Ethernet Bridge 52Contact InformationFor help with the installation or operation of this product, contact LinksysCustomer Support at one

Phoneline 10M Cable/DSL RouterTroubleshooting 30Common Problems and Solutions 30Frequently Asked Questions 32Appendix 36How to Ping Your ISP’s E-mail

© Copyright 2000 Linksys, All Rights Reserved.http://www.linksys.com

Phoneline 10M Cable/DSL Router• One HomeLink™ Phoneline 10M Cable/DSL Router• One AC Power Adapter • One User Guide and Registration Card• Windows 95,

Phoneline 10M Ethernet Bridge 4Getting to Know the HomeLink Phoneline 10M Cable/DSLRouterRear Panel PortsPhone Use this port for connecting your telep

Power The Power LED will light up when the HomeLinkPhoneline Router is powered on. Note that there is noON/OFF switch; simply plug in the power adap

The following instructions will have your HomeLink Phoneline Router up andrunning in minutes.Basic Installation1. Make sure that every component of y

If your network connections begins acting erratically, you may want to reset theHomelink Phoneline Router. To reset your Homelink Phoneline Router, do

3. The HomeLinkPhoneline 10MCable/DSLRouter’s Setuppage will appear.4. Configure the following values.Router Name & Domain Name These fields allo