Linksys WAP54G User Manual

Wireless-G Access PointUse this guide to install: WAP54GUser Guide

1312Wireless-G Access Point9. The second Security Settings screen, shown in Figure 5-8, shows the WEPkey. If you entered a passphrase, then the Key 1

Wireless-G Access Point1514LAN• MAC Address. The MAC Address of the LAN (Local Area Network)interface is displayed here.• Configuration Type. Select S

Wireless-G Access Point1716Wireless• MAC Address. The MAC Address of the wireless (2.4 GHz, Draft802.11g) interface is displayed here.• Mode. Select M

Wireless-G Access PointSETTING THE AP MODE:The Access Point offers two modes of operation: Access Point and WirelessBridge. For all bridging modes, ma

Wireless-G Access Point21The Status tab, shown in Figure 6-8, will display current information on theAccess Point, its settings, and its performance.•

Wireless-G Access Point2322To view a log of the Access Point’s activity, select the Log tab, shown in Figure6-9.Log. To enable permanent logging activ

Wireless-G Access Point2524To upgrade the Access Point’s firmware:1. Download the firmware upgrade file from the Linksys website.2. Extract the firmwa

Wireless-G Access Point2726Before making any changes to the Advanced Wireless tab, shown in Figure 6-13, please check your wireless settings on your o

Wireless-G Access Point2928The SNMP screen allows you to customize the Simple Network ManagementProtocol (SNMP) settings. SNMP is a popular network mo

Wireless-G Access PointWhat is Roaming?Roaming is the ability of a portable computer user to communicate continu-ously while moving freely throughout

COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Linksys is a registered trademark ortrademark of Cisco Systems, Inc. a

Wireless-G Access PointWhat is WEP?WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 40-bitshared-key algorithm, as described in th

Wireless-G Access PointAppendix B: Setting Up the TCP/IP andIPX ProtocolsBefore a computer can communicate with the Access Point, it must be config-ur

Wireless-G Access Point1. Click the Start button, select Settings, and open the Control Panel. Insidethe Control Panel, double-click the Network icon.

Wireless-G Access Point4. Select NWLink IPX/SPX/NetBIOS Compatible Transport Protocolfrom the list and click the OK button. 5. When the Network wind

Wireless-G Access Point4140Browser - A browser is an application program that provides a way to look atand interact with all the information on the Wo

Wireless-G Access Point4342Dynamic IP Address - An IP address that is automatically assigned to a clientstation in a TCP/IP network, typically by a DH

Wireless-G Access PointMulticasting - Sending data to a group of nodes instead of a single destination.Network - A system that transmits any combinati

Wireless-G Access Pointunits of data (called packet) that a message is divided into for efficient routingthrough the Internet. TCP/IP (Transmission Co

Wireless-G Access Point49Appendix D: SpecificationsStandards IEEE 802.11g, IEEE 802.11bChannels11 Channels (USA)13 Channels (Europe)14 Channels (Japan

Wireless-G Access Point5150Appendix F: Contact InformationFor help with the installation or operation of this product, contact LinksysTechnical Suppor

Wireless-G Access PointTable of ContentsChapter 1: Introduction 1The Instant Wireless Wireless-G Access Point 1Features 1Chapter 2: Planning Your Wire

© Copyright 2003 Linksys, All Rights Reserved.http://www.linksys.com

Wireless-G Access PointChapter 1: IntroductionWireless-G Access PointWireless-G is the upcoming 54Mbps wireless networking standard that'salmost

Wireless-G Access PointChapter 3: Getting to Know theWireless-G Access PointThe Access Point’s ports, where a network cable is connected, are located

Wireless-G Access PointChapter 4: Connecting theWireless-G Access Point 1. Locate an optimum location for the Access Point. The best place for theAcc

Wireless-G Access Point3. The following screen, shown in Figure 5-2, displays how the Access Pointis configured in this Setup Wizard. Optimally, you s

Wireless-G Access Point6. As shown in Figure 5-5, the IP Settings screen will appear next. Enter anIP Address, Subnet Mask, and enter a unique name f

Wireless-G Access Point8. The Security Settings screen (Figure 5-7) will appear next. From thisscreen, you will set the Wired Equivalent Privacy (WEP