Linksys SPA9000 User Manual Page 72
- Page / 128
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
65
Chapter 6: Using the Web-based Utility
The Voice Tab
IP Telephony System
The Voice - Line 1/2/3/4 Screen
Use the appropriate screen to configure settings for each external Internet phone line.
Line Enable. To enable this line for service, select yes. Otherwise, select no. The default is yes.
Network Settings
SIP ToS/DiffServ Value. Enter the TOS/DiffServ field value in UDP IP packets carrying SIP messages. The default
is 0x68.
SIP CoS Value. Enter the CoS value for SIP messages. The default is 3.
SIP Settings
SIP Port. Enter the port number of the SIP message listening and transmission port. The default is 5060.
SIP 100REL Enable. To enable the support of 100REL SIP extension for reliable transmission of provisional
responses (18x) and use of PRACK requests, select yes. Otherwise, select no. The default is no.
Auth Resync-Reboot. If this feature is enabled, the System will authenticate the sender when it receives the
NOTIFY resync reboot (RFC 2617) message. To use this feature, select yes. Otherwise, select no. The default
is yes.
SIP Proxy-Require. The SIP proxy can support a specific extension or behavior when it sees this header from the
user agent. If this field is configured and the proxy does not support it, then it will respond with the message,
“unsupported.” Enter the appropriate header in the field provided.
SIP Remote-Party-ID. To use the Remote-Party-ID header instead of the From header, select yes. Otherwise,
select no. The default is yes.
SIP Debug Option. SIP messages are received at or sent from the proxy listen port. This feature controls which
SIP messages to log. Select none for no logging. Select 1-line to log the start-line only for all messages. Select
1-line excl. OPT to log the start-line only for all messages except OPTIONS requests/responses. Select 1-line
excl. NTFY to log the start-line only for all messages except NOTIFY requests/responses. Select 1-line excl. REG
to log the start-line only for all messages except REGISTER requests/responses. Select 1-line excl.
OPT|NTFY|REG to log the start-line only for all messages except OPTIONS, NOTIFY, and REGISTER
IMPORTANT: In most cases, you should not change the service settings unless instructed to do
by your ITSP.
Figure 6-44: Voice - Line 1 Screen - Network Settings
Figure 6-45: Voice - Line 1 Screen - SIP Settings
VoIPon Solutions www.voipon.co.uk [email protected] Tel: +44 (0) 1245 600560
- IP Telephony 1
- Copyright and Trademarks 2
- How to Use this Guide 2
- Table of Contents 3
- List of Figures 5
- Chapter 1: Introduction 8
- What’s in this Guide? 9
- IP Telephony System 10
- A Typical Scenario 11
- The Back Panel 13
- The Front Panel 14
- Chapter 4: Getting Started 15
- Internal Calls 16
- Connect the Internet Phones 18
- External Calls 19
- Action Command 22
- (press these 22
- Choices Description 22
- Entering a Password 26
- Auto-Attendant Messages 27
- 1 to Record 28
- 2 to Review 28
- 3 to Delete 28
- * to Exit 28
- The PBX Status Screen 30
- Parking Lot 31
- Line 1 Calls 31
- The Router Tab 32
- The Router - WAN Setup Screen 34
- MAC Clone Settings 35
- Remote Management 35
- QOS Settings 35
- The Router - LAN Setup Screen 36
- Port Forwarding Settings 37
- DMZ Settings 37
- System Reserved Ports Range 37
- The Voice Tab 38
- Line 1/2/3/4 Status 40
- Auto Attendant Prompt Status 40
- The Voice - System Screen 41
- The Voice - SIP Screen 42
- SIP Timer Values (sec) 43
- Response Status Code Handling 44
- RTP Parameters 44
- SDP Payload Types 44
- NAT Support Parameters 45
- PBX Parameters 46
- Auto Attendant Parameters 49
- PBX Phone Parameters 51
- Configuration Profile 52
- Firmware Upgrade 53
- General Purpose Parameters 54
- The Voice - Regional Screen 55
- Distinctive Ring Patterns 56
- Control Timer Values (sec) 58
- Miscellaneous 63
- The Voice - FXS 1/2 Screen 66
- Subscriber Information 67
- Dial Plan 68
- Streaming Audio Server (SAS) 68
- Call Feature Settings 68
- Audio Configuration 69
- Network Settings 72
- SIP Settings 72
- NAT Settings 75
- Proxy and Registration 75
- Appendix A: Troubleshooting 77
- For Windows 2000: 80
- For Windows XP: 80
- Ending Ports 84
- Protocol IP Address 84
- For Netscape 4.7 or higher: 86
- Frequently Asked Questions 87
- 4 “Goodbye.” 90
- Recording a New Prompt 91
- Advanced Users 94
- AA Dial Plan 1 dp1 96
- AA Dial Plan 2 dp2 96
- Internal Dial Plan 97
- 4“Goodbye.” 98
- Parameter Description Type 101
- Parameter Value 103
- Overview 106
- Before You Begin 106
- Ethernet Adapter 109
- Appendix F: Windows Help 111
- Appendix G: Glossary 112
- Appendix H: Specifications 117
Related products and manuals for Networking Linksys SPA9000
Networking Linksys WET54GS5 User Manual
(69 pages)
(69 pages)
Networking Linksys EG0801SK User Manual
(44 pages)
(44 pages)
Networking Linksys PCMLM56 User Manual
(29 pages)
(29 pages)
Networking Linksys USB100TX User Manual
(28 pages)
(28 pages)
Networking Linksys EG24M User Manual
(46 pages)
(46 pages)
Networking Linksys HM-BT-VIN User Manual
(8 pages)
(8 pages)
Networking Linksys EG1032 V3 User Manual
(46 pages)
(46 pages)
Networking Linksys NULL WPC55AG User Manual
(27 pages)
(27 pages)
Networking Linksys USB1000 User Manual
(26 pages)
(26 pages)
Networking Linksys USB200HA User Manual
(22 pages)
(22 pages)
Networking Linksys WTR54GS User Manual
(86 pages)
(86 pages)
© 2020, manymanuals.com. All rights reserved. | 0.911 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals